Good morning! I hope you are all ready for a home economics lesson today because Iβm sharing a tutorial for an easy thread catcher. My girls each made one for their new sewing machines and I made one too!
So what is a thread catcher?
Itβs basically a super cute trash can with a weighted pin cushion on top. These hang nicely by your sewing machine and come in very handy when it comes to keeping little pieces of thread, and fabric contained. Plus you can quickly access your pins while sewing too. And who doesnβt need a cute little trashcan in their sewing room?
This post got a tad long, but I wanted to give you as many details as I could. By the way, this is a great project for younger sewers! My girls (9 and 11) each made their own bags. I did cut the fabric for them, but they did the rest all on their own.
Sound like fun? Letβs get started!
Supplies:
-
- –> Download a FREE printable pattern for the Thread Catcher <–
- Pins
- Rotary cutter
- Scissors
- mat and ruler
- sewing machine (Or a needle and thread but who has time for that?)
- Fabric (Fat quarters work nicely, but youβll need 1- 17.5βx11β of the outside fabric, and 1 full Fat Quarter or 18βx 22β piece of the lining fabric.)
- 1/2β x 18β of any type of stabilizer for the top edge of the bag. I used a cotton belting similar to this one from JoAnnβs, but you can use plastic or anything else you have on hand that will give it some stability.
- Rice, sand, or crushed walnut shells for pillow filling (walnut shells can be purchased at the pet store, they are used for lizard cage bedding.)
All seems are sewn at 1/4β unless otherwise indicated.
Cutting Instructions:
From your outside fabric cut:
-
- 1 – 3.5βx 10β strap piece**
- 1 β 4.5β x 10β pillow piece
- 1 β 17.5β x 8.5β bag outside piece
(**NOTE: The strap in the PDF Pattern size has been updated to make itΒ tad smaller. It is now 3-1/2″ x 6″. You can use whichever size you prefer!)
From your inside lining fabric cut:
-
- 1 β 17.5β x 11β bag lining piece
The Strap:
The first step is to create the strap that holds the pin cushion to the bag. To do this simply fold the strap piece in half length wise with the right sides together, so your piece measures 3.5β x 10β. Sew down both sides using a 1/4β seam. Make sure to leave one end open.
Turn the strap right sides out and push out the corners with a pencil, or your scissor tip. Just be careful not to cut your fabric!
The Pillow:
Next lay the strap you just created on the piece of pillow fabric as shown below. Fold the pillow fabric right sides together in half so it measures 4.5βx 5β.
Adjust the strap so itβs centered on the pillow. Pin all of the layers together. Stitch down both sides, and about a 1/2β in on each end, but make sure to leave an opening in the end so you can turn your pillow right sides out and fill!
When stitching, make sure to catch your strap in the bottom seam (shown below), but fold down your strap so you do NOT stitch your strap in the top seam.
Turn your pillow right side out. It should look like thisβ¦
Take a quick minute to press your pillow and strap. We also tucked the pillow opening seam in to make sewing it up a little easier.
If youβd like, do a 1/4β top stitch around the outside of the pillow edge to give it a more finished look. This is a picture of my daughter’s project, I forgot to top stitch my pillow Again, make sure to leave one end open to fill!
Next fill your pillow with either rice, sand, or crushed walnut shells.
Then tuck in your edges and top stitch to close the seam. This is much less noticeable if you top stitch like I did in my daughterβs project shown above. Set your completed pillow and strap aside.
The Bag:
Next pin your lining and outside bag fabric right sides together along the 17.5β sides and pin. Sew together with 1/4β seam.
Press your seam open so that you have a nice edge.
Next turn your project sideways and fold in half like shown below. Pin along the edge and add in the stabilizer for the bag rim so it goes all the way around the project as well. Line it up so itβs just along the seam of the inside lining as shown below and pin in place.
Stitch around all three sides as shown below, making sure to catch the stabilizer in your seam. Trim the stabilizer off even with your bag fabric when done sewing. Make sure to leave about 3β at one end open so you can turn the bag.
Next fold your ends like shown below.
Mark about 1.5β up from each corner tip and sew along your line. This will create a box look on the bottom of your bag. Do this on both tips of your outside and lining fabric.
After youβve sewn along your line, trim off any excess fabric like below.
Your bag should now be looking like thisβ¦
Next turn your bag right side out and stitch up the end seam to finish it off.
Tuck your inside lining down into your bag so it should look something like this, with about an inch of your inside lining showing along the top edge.
Next run a quick top stitch around the edge just to keep the lining and stabilizer strip in place.
The Big Finale:
Adding your strap to your bag is the last step in completing your project! Place your strap along the center back side of your project about 2.5β down and pin it in place.
Just make sure you only pin it to one side of your bag, and not both sides or your bag wonβt open when youβre done!
I just stitched a square around the strap and then an βXβ inside to make it a little bit more secure.
And thatβs it! This project took us about an hour and turned out really cute!
Now go and make some more because theyβre fun!
Oh and donβt forget to get some fun pins to add to your cushion. No sewer is complete without a cute set of pins.
Then itβs time to put your new bag to use! Any small scraps, threads, bits, and bobs can go in here.
–> Download a FREE printable pattern for the Thread Catcher <–
I hope you enjoyed this tutorial and happy sewing!
These are cute, I made mine at least 20yrs ago & use it so much , I also crochet & the bag is great to pUT the yarn ends in when I weave in tails,
I wish I had left the three inch opening on the inside part before right-side outing the bag. Other than that this was a fun project. Thank you!
I love this project. Made two now. One for myself and one for my friend .
Thank you x
Now that I am trying for a zero waste sewing room, I can use several of these! Some for threads, some for tiny quilting cotton cut off and some for garment fabric bits – all destined for collage work. These are so cute and functional. Thanks for sharing this great tutorial and pattern.
I look forward to making this. It occurs to me that the weighted bags on either side of chair arm rest covers would be good.
What an excellent tutorial. Thank you for sharing.
I wish you would have shown images of your stabilizer in the images after you have sewn it…i feel like i wasted that material now since you didnt use it except for 1 stitch.
Hi Holly,
I’m not sure what you mean by wasting material, but the stabilizer helps hold the top edge of the scrap bin so that it keeps its shape. Without it you would have a very floppy scrap bin π
Thank you so much for this fun tutorial! I made one for my sister who just moved into her new home and will finally have a sewing room again for the first time in a decade. I didn’t have any cotton web/belting or ANYTHING similar in my stash so I cut a strip from a large Christmas tote bag – it worked perfectly! π
Thank you for this tutorial. I can’t believe I went so long without this little bag hanging off of my sewing table! I almost bought one of these, and then I searched online and found your tutorial and made it myself. Thank you!
You’re welcome, so glad you like them!
I am a complete beginner (I bought myself a sewing machine this Christmas) and tonight Iβve managed to start and complete this project. I am so happy with how it turned out!
Thanks so much for the detailed and straightforward instructions. I love it π
Thank you so much for this tutorial. I did find, though, that I had to tack the stabilizer to the seam allowance as when I turned the bag out, the stabilizer didn’t turn with it and ended up as a lump on one side! I unpicked the closing seam, stitched the stabilizer and resumed the process with no further trouble! This will be a great addition to my sewing area.
Oops! Yes, fusible fleece is a great way to stop that from happening and also if you quilt it a little that is a great way too!
I love the quilting idea – you could also monogram a name or initials or embroider a border along that top edge; the mind boggles! – and that would really hold the *mouth* open a bit better than the stabilizer does. I have since made another for a friend and have the fat quarters waiting to make yet another for another deserving friend! I used a full 1 inch width of the waist stabilizer rather than cutting it down to a half inch. Thank you again so much!
Hi, of course you can do anything you want on your thread catcher! I think embroidering the border would be lovely π